We use cookies to improve your browsing experience. By continuing to use our site, you accept our cookie policy.

close Close Cookie Notification
Instron
  • Back
  • Home
  • Produkty
    Urządzenia testujące
    Maszyny Wytrzymałościowe - Zrywarki
    Wytrzymałość strukturalna
    Automatyczne systemy testujące
    Dynamiczne i zmęczeniowe systemy testujące
    Symulatory zderzeń
    Testery skręcania
    Reometry i Plastometry (MFT)
    Młoty zrzutowe i młoty wahadłowe
    HDT i Vicat
    Produkty poprzednich generacji
    AKCESORIA
    Oprogramowanie
    Głowice pomiarowe
    Oddzieranie, tarcie, przebicie
    Komory temperaturowe i Piece
    Uchwyty do rozciągania
    Uchwyty do badania ugięcia
    Płyty kompresyjne
    Systemy i akcesoria biomedyczne
    Ekstensometry
    Composite Fixtures
    Uchwyty do badania elektroniki
    Pomiary i przygotowanie próbek
    All Accessories
    Katalog akcesoriów
  • Rozwiązania branżowe
    Search by Material Search by Standard Search by Test Type
    Industries
    Automotive
    Biomedical
    Electronics
    Materials
    Composites
    Metals
    Plastics
  • Serwis i wsparcie
    Instron Remote Technical Support CYKL ŻYCIA PRODUKTU Historie serwisowe Szkolenia
    USŁUGI
    Kalibracja i weryfikacja
    Usługi wdrożeniowe Instron
    Instalacja i przeniesienie
    WSPARCIE TECHNICZNE
    FAQ Często zadawane pytania
    Usługi aktualizacji oprogramowania
    ZASOBY
    Instrukcje
    Lokalizator numerów seryjnych
  • Nasza firma
    KARIERA Informacje prasowe NEWSLETTERY
    O NAS
    Nasza historia
    Lokalizacje
    Akredytacje i certyfikaty
    ZASOBY
    Słownik
    Typy testów
    Biuletyny
    Literatura
    Aktualności
    Poradnik
    Webinaria
    Studia przypadku
  • Skontaktuj się z nami
  • Polska
Testing Solutions » By Test Type » Rheology » ISO 1133-2 & ASTM D1238

ISO 1133-2 and ASTM D1238: When Load Cell Ensures Repeatability of Results

Standard

  • ISO 1133
  • ASTM D1238

Specimen

  • Tabletki
  • Proszek

Test Types

  • Rheology

Materials

  • Tworzywa Sztuczne
  • Guma/Elastomery

Business Sector

  • Consumer/Industrial Products
  • Contract Testing Services
Contact usView Accessories Catalog
  • Description
  • Literature

Melt Flow Rate (MFR) and Melt Volume-Flow Rate (MVR) can normally be obtained with easy and quick test procedures. Test standards specify detailed test conditions, including pre-heating period, starting position, and measurement length/time. However, when using a basic melt flow tester (extrusion plastometer), fulfilling all standard specifications can be challenging with some polymers and compounds, and results can be affected by poor repeatability.

It's not uncommon that during the pre-heating period the sample swells and pushes the piston up, especially when testing under low-load conditions (e.g. less than 2.16 kg). Applying a compacting force higher than the test weight can prevent this from happening, and if precise positioning of weight lifting device is possible, the starting position and timing for measurements can be set in a much more repeatable way.

Some samples show very high viscosity and effective compacting requires high loads. Air bubbles trapped inside as a result of poor compacting can affect the MFR/MVR results. A high, but controlled, compacting force is needed. Plus, at the end of tests, the same force can be applied for purging out the remaining material, reducing the total test cycle time.

We tested an HDPE sample with an expected MFR of about 0.25 g/10 min (190 °C, 2.16 kg) with a CEAST MF30, applying ISO 1133-2 Procedure B. CEAST MF30 has a load cell integrated with the weight lifting device, giving the possibility to apply up to 750 N of compacting force. To compare the repeatability of results, we performed twenty consecutive tests using the load cell for compacting, and another twenty without (so using only the test weight to compact). The average MFR result was close to the expected value in both cases. However, results from the tests performed without the load cell were consistently higher and with a standard deviation of 0.012 g/10 min (close to 5%), whereas tests where the load cell was compacted the standard deviation was as low as 0.005 g/10 min (2%). Similar results were obtained also following ASTM D1238 Procedure B.

CEAST Melt Flow Series Brochure

Flow properties of molten plastics are a critical characteristic requiring good knowledge and control. The Instron® Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Mass-Flow Rate (MFR) and the Melt Volume-Flow Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests.

  • Products
  • 7/3/2013
  • 1.1 MB

Region Selector

Dismiss Region Selector

Americas

  • North America
  • Brasil
  • South America

All Other Countries

  • Global Site

Europe

  • France
  • Deutschland
  • Italia
  • Polska
  • España
  • Türkçe
  • United Kingdom

Asia Pacific

  • 中国
  • India
  • 日本
  • 대한민국
  • 台灣
  • ประเทศไทย
Instron Logo White
Dane kontaktowe

Dział handlowy: +48 603 779 585

Serwis: +48 691 016 100

PRZYDATNE LINKI
  • Systemy testujące
  • Oprogramowanie
  • Akcesoria
  • Katalog
  • Słownik
  • Biblioteka
  • Rozwiązania do badań i testów
  • Newsletter
  • Webinaria
  • Studia przypadku
  • Wydarzenia
  • Kariera
Policies / Legal
  • Polityka prywatności i plików cookie
  • Warunki korzystania
  • Dostępność
  • Kontrola eksportu
  • Informacja o danych RODO
Skontaktuj się z nami
ZAPISZ SIĘ DO NASZEGO NEWSLETTERA
ADRES E-MAIL
© Illinois Tool Works Inc. All rights reserved.
[email protected]
  • Polityka prywatności i plików cookie
  • Warunki korzystania
  • Dostępność
  • Kontrola eksportu
  • Informacja o danych RODO